Ng’eyo matiyo kuom valve

Fundasi mar valv
1. Pimo madongo mag valv gin: presa mapile PN kod diamita mapile DN
2. Tich maduong’ mar valve: ng’ad gik ma oriwre, lok kaka pi ng’ado, kendo lok yo ma pi ng’ado
3, yore madongo mag tudruok mar valve gin: flanj, thread, lodo, wafer
4, ng’wech mar valve —— ng’wech mar liet nyiso ni: gik mopogore opogore, ng’wech mopogore opogore mag tich, ng’wech ma malo ma ok owinjore ma tiyo opogore .
5. Nitie yore ariyo madongo mag ng’ado bura: yore mag piny Ulaya kod yore mag piny Amerka.
Gik ma tudruok mag paip mag sistem ariyogo opogore ahinya kendo ok nyal pimogi;
En gima owinjore ahinya mondo ipogruok kaluwore gi rang’iny mar presa:
1.6, 2.5, 4.0, 6.3, 10.0, 16.0, 25.0, 32.0, 40.0MPa;
Sistem mar piny Amerka en PN1.0 (75), 2.0 (150), 5.0 (300), 11.0 (600), 15.0 (900), 26.0 (1500), 42.0 (2500) MPa.
Kido madongo mag flange mar paip gin: ng’injo (IF), ng’injo mar plate (PL), ng’injo mar ng’ut (SO), ng’injo mar ng’ut (WN), ng’injo mar soket (SW), ng’injo mar ng’injo (Th), ng’injo mar ng’injo mar ng’injo (PJ / SE) / (LF / SE), ng’injo mar ng’injo (PJ / SE), kod mamoko (PJ/RJ).
Kido mar lowo mar singo mar flange oting'o ahinya: lowo ma opong'o (FF), lowo ma owuok oko (RF), lowo ma ochung' motegno (FM), lowo ma oting'o ring'o (RJ), kod mamoko.

Valve ma pile (ma pile)
1. Z, J, L, Q, D, G, X, H, A, Y, S kaluwore kod kod mar kit valv nyiso: valv mar rangach, valv mar geng'o, valv mar throttle, valv mar ball, valv mar winyo, valv mar diaphragm, valv mar plug, valv mar ng'iyo, valv mar arita, valv mar golo pi.
2, Kod mar tudruok mar valve 1,2,4,6,7 kaka giluwore ne owacho ni: 1-thread ma iye, 2-thread ma oko, 4-flenj, 6-welding, 7-klip mar ariyo
3, Yo mar lando kod mar valve 9,6,3 kaka giluwore ne owacho ni: 9-matiyo gi stima, 6-matiyo gi yamo, 3-matiyo gi stima.
4, Kod mar gik moko mag valve Z, K, Q, T, C, P, R, V kaka giluwore ne owacho ni: chuma ma ng’we ng’ar, chuma ma ng’we ng’ar, chuma ma ng’we ng’ar ma ng’we ng’ar, kopa kod aloi, chuma mar kabon, chuma ma ok ng’ich, chuma ma ok ng’ich.
5, Oboke mar kombe kata kod mar ng'ut R, T, X, S, N, F, H, Y, J, M, W kaka giluwore: chuma ma ok mak chilo ma austenitic, chuma ma ok mak chilo, raba, plastik, plastik mar nailon, plastik mar fluorine, chuma ma ok mak chilo mar Cr, chuma matek mar ng'ut, raba mar ng'ut, gik ma nigi ringruok mar valve.

6. Gin gik adek madongo mage ma owinjore ipar e wi yiero ng’at ma biro tiyogo?
1) Output mar actuator biro bedo maduong’ moloyo ting’ mar valve ma rito gik moko kendo nyaka bed ni owinjore.
2) Mondo irang’e ng’injo ma ng’ato nyalo ng’ado, pogruok ma oyienegi mar presa ma valve ma rito ng’ato nyalo chopo dwaro mag yo ma itiyogo. Teko ma ok owinjore mar core mar valve onego ogol e kinde ma pogruok maduong’ mar presa.
3) Kapo ni dwoko mar ng’at ma timo gik moko nyalo chopo dwaro mag tich mar ng’ado bura, ahinya ahinya ng’at ma tiyo gi stima.
7, TWS ng’at ma nigi ng’ol nyalo chiwo ng’at ma nigi ng’ol?
Valv mar winyo moting'o raba: valv mar wiya mar wafer, valv mar wiya mar lug,valv mar wiya mar flanj; valv mar dho rangach; valv mar ng’iyo;valv mar keto rom, valv mar ball, kod mamoko.
E Kambi mar Tianjin Tanggu, wabedo gi mor kuom chiwo gik ma nigi rang’iny mokwongo ma luwo chike ma malo moloyo mag ng’iepo. Ka watiyo gi valve kod gik ma watiyogo mathoth, inyalo geno ni wabiro chiwo dwoko maber moloyo mar sistem mari mar pi. Tudri kodwa sani mondo ing’e mathoth kuom gik ma watiyogo kod kaka wanyalo konyi.